- Our Products
- Fire Detectors
- Gas Detectors
- Control Panels
- Custom Gas Detectors
- Custom Systems
- About Us
- Customer Support
- Industry News
- Contact Us
Installation and Calibration Accessories include junction boxes for mounting sensors on walls, ceilings or air ducts. Also accessories to protect sensors from water or dust, and test gas for verifying sensor performance.
These accessories are used with the SST Model GC800 Combustible Gas Sensor, GC801 NOVA-Sensor®, GT810 Toxic Gas Sensor, GT811 NOVA-Sensor®, GT820 Oxygen Deficiency/Enrichment Sensor, or GT821 NOVA-Sensor®. They provide additional features or protection as described below.
Rain Shield for installation on front of sensor housing. Protects the sensor from dripping rain and blowing snow. The rain shield slips over the front of the sensor and is held in place with set screws. A metal screen is permanently installed in the front of the housing to trap rain drips or snow flakes before they reach the sensor. For additional protection, a dust cover accessory may be snapped onto the front of the rain shield.
Dust Cover for installation on front of sensor housing, or on front of the rain shield. A 40 micron filter protects the sensor from being contaminated by dust or oil droplets. Also effective in shielding the sensor from high wind environments.
Sampling Block (not pictured) can be installed on sensor and used to extract a sample of the atmosphere from an area where sensor cannot be normally mounted directly. Block is connected to sampled volume with stainless steel tubing, and a vacuum pump is used to extract a sample of the air for application to the sensor. Includes connection for calibration gas.
Remote Calibration Adapter is installed onto the front of sensors that are located in inaccessible locations. The calibration adapter acts as both a rain shield and dust cover, and also includes a connection for introduction of calibration gas via tubing routed to a convenient location. We recommend the use of “Tygon” tubing. Or the supplied tubing connector may be removed and replaced with a suitable compression fitting if metal tubing is preferred.
Duct Mounting Assembly is used to install the gas sensor directly on a heating or air conditioning duct for monitoring the air in the duct. Includes connection for introducing calibration gas into the sensor.
Portable Purge Calibrators include a valve, flow regulator, pressure gauge, and tubing with adapter cup to introduce test gas onto the sensor. The calibrators screw onto test gas cylinders. The refillable cylinder type calibrator is for use only with combustible gas sensors. Each refillable cylinder contains 3.6 cubic feet (103 liters) of test gas, which provides approximately 120 normal calibrations per cylinder. Refill service is available from Safety Systems Technology. The disposable cylinder calibrator may be used for either combustible or toxic gasses. Disposable cylinders contain 2 cubic feet (58 liters) of gas, approximately 40 normal calibrations.
Gas Collection Cone attaches to the front of combustible or toxic gas sensors. Used with loghter-than-air gases (hydrogen, ammonia, etc.) to improve detection capability. All stainless steel construction. Includes connection for introducing calibration gas onto the sensor.
|851-1||Rain Shield, Stainless Steel|
|851-2||Rain Shield, Anodized Aluminum|
|852-1||Dust Cover; Stainless Steel Mounts directly to toxic gas sensors. 851-1 or 851-2 required to use dust cover on combustible gas sensors.|
|853-1||Gas Sampling Block|
|854-1||Duct Mounting Assembly, Stainless Steel|
|854-2||Duct Mounting Assembly, Anodized Aluminum|
|856-01||Portable Purge Calibrator for use with refillable test gas cylinders|
|856-**||Cylinder of Test Gas, refillable type|
|857-01||Portable Purge Calibrator for use with disposable test gas cylinders|
|857-**||Cylinder of Test Gas, disposable type|
|858-1||Remote Calibration Adapter, Stainless Steel|
|858-2||Remote Calibration Adapter, Aluminum|
|859-1||Gas Collection Cone, Stainless Steel|